发动机机油滤清器虑层强度分析及优化

针对机油滤清器工作工况下进出口压差、机油滤层强度及导流桩高度等问题, 通过试验测试与仿真相结合, 对滤清器初步设计进行了评估及优化, 以确保滤清器在工作工况下进出口压降及滤层强度能满足要求. 首先进行滤层性能试验, 得到滤层的惯性阻力系数和黏性阻力系数; 再通过滤层多孔介质CFD分析, 对滤清器进出口压降进行分析计算. 结果表明: 在-18℃、25℃和70℃的工况下, 进出口压降都小于10kPa, 满足相关要求. 针对滤层的最大主应力超过其抗拉强度的问题, 通过CAE仿真分析, 优化滤层与导流桩间隙, 将滤层最大主应力由110.1MPa降至36.99MPa, 小于其抗拉强度42.8MPa.     

航空导管弯曲试验的疲劳裂纹萌生寿命

飞行器液压导管受接头和卡箍等约束，在使用的振动环境中，会因弯曲应力而导致破裂，影响到飞行安全．本文对飞行器液压系统通用的不锈钢导管的裂纹萌生寿命进行了试验研究．首先在对8 mm、12 mm 无缺陷导管和含U 型缺口8 mm 导管的疲劳试验和有限元分析的基础上，得到了导管的最大拉应变-裂纹萌生寿命数据．然后采用基于强度极限和弹性模量估算法的Manson-Coffin 公式来预测导管裂纹萌生寿命．最后引入加载类型修正系数、表面质量修正系数、试样尺寸修正系数、应力集中敏感系数和有效应力集中系数，使修正后的公式对三种类型的导管均有较好的裂纹萌生寿命预测精度．     

甲烷浓度对碳化硅基底金刚石薄膜摩擦性能影响

利用热丝化学气相沉积法(HFCVD)在碳化硅基底上制备金刚石薄膜,采用场发射扫描电子显微镜、拉曼光谱仪、原子力显微镜研究了在不同甲烷浓度条件下制备的金刚石薄膜表面形貌及物相组成,在干摩擦条件下通过往复式摩擦磨损实验测试并计算了已制备金刚石薄膜的摩擦系数和磨损率,结合物相分析及摩擦磨损实验结果分析了甲烷浓度的改变对金刚石薄膜摩擦磨损性能的影响。结果表明,由于甲烷气体含量的升高,金刚石薄膜结晶质量下降,薄膜由微米晶向纳米晶转变。摩擦磨损实验结果显示:3%甲烷浓度条件下制备的金刚石薄膜耐磨性较好,磨损率为2.2×10^-7 mm³/mN;5%甲烷浓度条件下制备的金刚石薄膜摩擦系数最低(0.032),磨损率为5.7×10^-7 mm³/mN,制备的金刚石薄膜的耐磨损性能相比于碳化硅基底(磨损率为9.89×10^-5 mm³/mN)提升了两个数量级,显著提高了碳化硅基底的耐磨性。     

Scattering of Laser Light from Mixed Micelles

Dynamic and static scattering of light was employed to investigate mixed micelles of two homologous anionic surfactants-sodium octyl sulfate and sodium hexadecyl sulfate, above the phase boundary temperature and critical micelle concentrations (cmc). The results indicate that the mixed micelles change from prolate to sphcrical as the molar ratio SOS/SHS increases from 1 to 8. Below 1 or above 8, the formation of micelles is due to one surfactant dissolving the other.     

恒流应力下E2PROM隧道氧化层的退化特性研究

在电容测量的基础上研究了薄隧道氧化层在恒定Fowler-Nordheim(F-N)隧穿电流下的退化情况. 这种退化是恒流应力和时间的函数，对恒流应力大小的依赖性更加强烈，隧道氧化层在F-N电流下的退化是注入电荷密度(Q_inj)的函数. 在较低Q_inj下氧化层中发生正电荷俘获，在较高Q_inj下发生负电荷俘获，导致栅压变化的反复. 关键词： 2PROM')" href="#">E²PROM 隧道氧化层 退化 恒流应力     

具Hardy-Sobolev临界指数的奇异椭圆方程多解的存在性

运用变分方法研究了下面问题-Δpu=μupx(s)s-2u f(x,u),x∈Ω,u=0,x∈Ω,多重解的存在性,其中Ω是一个具有光滑边界的有界区域.     

Extrusion of pastes with a piston extruder for the determination of the local solid and fluid concentration, the local porosity and saturation and displacement profiles by means of NMR imaging

 Nuclear Magnetic Resonance (NMR) was used to investigate the extrusion behaviour of PTFE pastes in a ram extruder. By means of ¹H-NMR imaging (MRI) it is possible to determine the local proton density and therefore, the local fluid concentration. The ¹⁹F-MRI provides the local solid concentration. Thus the local saturation and the local porosity can be calculated with the information of the local fluid and solid concentration. Furthermore displacement profiles can be derived from NMR images by means of correlation techniques without any preparation or marking of the pastes. Received: 8 May 2000   Accepted: 1 May 2001     

Stress Distribution in an Infinite Elastic Body with a Locally Curved Fiber in a Geometrically Nonlinear Statement

Within the framework of a piecewise homogeneous body model, with the use of three-dimensional geometrically nonlinear exact equations of elasticity theory, a method for determining the stress—strain state in unidirectional fibrous composites with locally curved fibers is developed for the case where the interaction between the fibers is neglected. All the investigations are carried out for an infinite elastic body containing a single locally curved fiber. Numerical results illustrating the effect of geometrical nonlinearity on the distribution of the self-balanced normal and shear stresses acting on the interface and arising as a result of local curving of the fiber are presented.__________Russian translation published in Mekhanika Kompozitnykh Materialov, Vol. 41, No. 4, pp. 433–448, July–August, 2005.     

Numerical analysis of turbulent structure in compound meandering open channel by algebraic Reynolds stress model

The turbulent flow in a compound meandering channel with a rectangular cross section is one of the most complicated turbulent flows, because the flow behaviour is influenced by several kinds of forces, including centrifugal forces, pressure‐driven forces and shear stresses generated by momentum transfer between the main channel and the flood plain. Numerical analysis has been performed for the fully developed turbulent flow in a compound meandering open‐channel flow using an algebraic Reynolds stress model. The boundary‐fitted coordinate system is introduced as a method for coordinate transformation in order to set the boundary conditions along the complicated shape of the meandering open channel. The turbulence model consists of transport equations for turbulent energy and dissipation, in conjunction with an algebraic stress model based on the Reynolds stress transport equations. With reference to the pressure–strain term, we have made use of a modified pressure–strain term. The boundary condition of the fluctuating vertical velocity is set to zero not only for the free surface, but also for computational grid points next to the free surface, because experimental results have shown that the fluctuating vertical velocity approaches zero near the free surface. In order to examine the validity of the present numerical method and the turbulent model, the calculated results are compared with experimental data measured by laser Doppler anemometer. In addition, the compound meandering open channel is clarified somewhat based on the calculated results. As a result of the analysis, the present algebraic Reynolds stress model is shown to be able to reasonably predict the turbulent flow in a compound meandering open channel. Copyright © 2005 John Wiley & Sons, Ltd.